Search found 594 matches

Typically, fork seals will be fine unless the bushings are worn out. Before you put the seals in, check the fork to slider fit. Simply wiggle the tube inside the slider. You really shouldn't feel much ...

So I understood part of the 2vs3 wire sensors but not all. Thank you Brent for filling me in!

Most of the 3 wire sensors are "Hall Effect" sensors that put out a digital signal. They read ...

Sorry guys, I was thinking about the 900 clutch Embarassed

I started out to do this same job as well. Is there anything between the two bearings that would prevent them from being pressed out/in from one side? Like a spacer or a ridge? beerchug

They shou ...

Everyone seem to be in love with power and talks about it endlessly but the truth is chassis and handling and brakes are first and foremost.

Every motorcycle I have ever raced or owned got the sus ...

I offered mine up for 150 and got called all sorts of names. And it's in pretty good shape. As a result, Im keeping it.

that,s the principle ref: Cb1300 rear shock mount - looks a bit more radical though
wonder if this is primarily a solution to achieve the desired shock rake angle whilst keeping clear of the chain ru ...

Jim, are you saying you will be using OEM 750F Comstars?
Do wider tires actually hold corners better? I always wondered about that.

No, when I said OEM I meant any stock wheels that are 17” and a ...

I know you wanted Suzuki wheels, but the F4i wheels are extremely light.

Somebody go get their calipers warmed up...

https://www.nutty.com/M25-X-6-Phil-Flat-Head-Machine-Screw_p_8924.html

It's a conspiracy.

Mine literally blew up yesterday at the gas station....

Pm to Tom, hopefully He's got one left.

A 50 shot of Nitrous would be fun as hell for a solid 10-15 seconds...

sounds to me like the ignition timing got advanced some how. Move the pulse generator plate the same direction as the engine spins a little bit, nail it down again and try it then. It wont take much b ...

Take everything apart. EVERYTHING. It's worth while too. You'll never ride anything that you'll be able to compare the transmission to. Ive done probably a dozen on the full race MX engines I've done ...

My bike put out 11.5V at idle. at about 4,000rpm 14v. when i sit at a red light and with the brake light on it will kill the motor sometime. I run a halogen and Dyna.

If you're still running the OE ...

I got a new battery just not a AGM.

Bike Master?

What is the payload cap of that bike ? Shocked

Must be 700+ lbs on it . 300 plus 400 ??

You sir, are being very very kind. Those women are 400+ each, at least.

But realize, just because you bleach y ...

if that thing ran, I would have ridden it home!

Partzilla web site has the 1100 13218 bearing as green and the 13219 bearing as yellow Rolling Eyes

That doesn't seem right Doesn't matter as the are NLA

Look up the 1982 CB900F bearings. They're st ...

I just got some from my Honda dealer. They were 10.00 each half shell so 100.00 for a full set. They also told me those bearings are used in quite a few models so they won't be discontinued any time s ...

Aren't the 900f bearings interchangeable with the 1100 rod bearings?

Yes, but they aren't the same p/n.

On Partzilla, you can right click on the p/n and see what it interchanges with. But it's ...

I was at Cook's Corner one afternoon when 5-6 of them went by with open exhausts and the riders were all suited up like MotoGp guys. I was embarrassed from 100 yards away.

But the work and finish it provides makes it worth it.............IMO

Captain

I agree, that's why I'm looking at it myself. I'm in a position right now that's frustrating to say the least. I ...

Hey Darren, do you mind if I ask which vapor blaster you picked up? Ive been looking at them myself.

Vaporhoning Technologies closed loop system. Bought an Eaton polar air 7.5hp 80 gallon V4 compre ...

Hey Darren, do you mind if I ask which vapor blaster you picked up? Ive been looking at them myself.

Seems like everyday I have something that would be considered a close call by most.

Glad you made it out. Not all of us do.

Some oil leaks are a feature, not a fault.

Your English roots are showing Laughing

Saw a post where Jim said it went well but it hurts like hell.

I hope jimbo is ok, but man, having someone hack into your knoggin has gotta leave one hell of a headache.

One thing you'll find on these things is the switches are basically junk. I'd be your non start issue is the button on the throttle housing. Mine did that randomly too when I first got it. I took the ...

Wishing him and his family the best. What a difficult time.